Power connections
Cuponal Busbar at 15% Copper, or ASTM B1005
Use Cuponal at 15% copper by volume for a standard rectangular or round section. Use ASTM B1005 when the order names a 20, 25, or 30 volume percent class.
On this page
Use Cuponal standard rectangular or round bar when the cladding is 15 percent copper by volume, 37 percent by weight, and the section can match the copper bar's dimensions. As of November 7, 2026, the Cuponal brochure and the Bruker busbar page both print that 15 percent figure for rectangular and round sections. Use the 20 percent by volume cladding, 45 percent by weight, when the section is a high-aspect size or an L or T profile. Use an ASTM B1005 bar when the order names Class 20A, 25A, 30A, 20H, 25H, or 30H. As of the same day, the ASTM page lists those six classes at 20, 25, or 30 volume percent copper, annealed or hard-worked. The 15 percent Cuponal line is outside that class list. Solid C110 copper remains the bar on the copper and aluminum page when the section cannot grow and the metal stays copper.
Standard Cuponal is 15 percent copper by volume
The brochure opened November 7, 2026 describes Cuponal as a solid core of electrical grade aluminium with a pressure-bonded seamless outer layer of high conductivity copper, made by hydrostatic extrusion. It says a copper bar can often be replaced by a Cuponal bar of equal dimensions. The Bruker busbar page, opened the same day, repeats that equal-dimension substitution and the maximum cost saving that comes with it. Both pages say all rectangular and round sections use a nominal copper cladding of 15 percent by volume, 37 percent by weight, with the exception of certain high-aspect sizes at nominally 20 percent by volume, 45 percent by weight. Special profiles, for example L or T shapes, are made to order at 20 percent copper by volume.
As of November 7, 2026, the brochure's standard supply is a length of 4000 mm, a maximum length of 6000 mm, a width range of 10 to 120 mm, a thickness range of 3 to 15 mm, a diameter up to 40 mm, and an area range of 20 to 1260 mm². Square and round edge bar is available. The brochure says Cuponal complies with BS 159:1957 and conforms to DIN 43670 Part 2. It says the aluminium core is electrical grade and the copper cladding is to BS 2871/C101. It says the bar is easy to bend, with less spring-back than copper, and that the relevant data sheet should be consulted for recommended bending radii. It does not print a radius on this brochure.
| Order line | Copper by volume | Where it is printed | Section the page names |
|---|---|---|---|
| Cuponal rectangular or round | 15 percent, 37 percent by weight | Brochure and Bruker busbar page | Equal dimensions to a copper bar, within the standard supply |
| Cuponal high aspect, L, or T | 20 percent, 45 percent by weight | Brochure and Bruker busbar page | High-aspect sizes, or an L or T made to order |
| ASTM B1005 Class 20A or 20H | 20 percent nominal | ASTM B1005-17 scope | Rectangular bar, annealed or hard-worked |
| ASTM B1005 Class 25A or 25H | 25 percent nominal | ASTM B1005-17 scope | Rectangular bar, annealed or hard-worked |
| ASTM B1005 Class 30A or 30H | 30 percent nominal | ASTM B1005-17 scope | Rectangular bar, annealed or hard-worked |
ASTM B1005 names six classes, and 15 percent is not one of them
The ASTM page opened November 7, 2026 says B1005-17 covers copper-clad aluminum rectangular bar for electrical bus applications. The product is a solid core of aluminum with a continuous outer copper layer bonded to the core throughout. Scope 1.2 lists six classes. Class 20A is nominal 20 volume percent copper, annealed. Class 25A is nominal 25 volume percent, annealed. Class 30A is nominal 30 volume percent, annealed. Class 20H, Class 25H, and Class 30H are the same three percents, hard-worked. Scope 1.3 says inch-pound units are the standard, except for resistivity and density, where SI units are the standard. The page says the specification also covers tensile properties, bend properties, interface bonding, density, electrical properties, edge contours, and dimensional tolerances. It does not print those test numbers on the public abstract.
A 20 percent Cuponal profile and a Class 20A or Class 20H bar share a nominal 20 volume percent figure and are still different order lines. Cuponal's 20 percent line, as of November 7, 2026, is the high-aspect exception and the L or T profile in the brochure. ASTM's Class 20 is one of six classes of rectangular bar, annealed or hard-worked. The brochure does not say Cuponal is supplied to ASTM B1005. The ASTM page does not mention Cuponal. Name the document the drawing uses. Equal-dimension substitution is a sentence on the Cuponal pages. It is not a sentence on the ASTM page.
The brochure also names the supply window and the approvals line
As of November 7, 2026, a Cuponal bar inside the standard supply is 10 to 120 mm wide, 3 to 15 mm thick, up to 40 mm in diameter, and 20 to 1260 mm² in area, at 4000 mm standard length or 6000 mm maximum. A round section at 15 percent copper is inside that diameter line. A rectangular section at 15 percent copper is inside the width and thickness lines. An L or T is the 20 percent profile line, and the brochure says enquiries for profiles should be made during switchgear design so the section can be checked. Square edge and round edge are both listed. The brochure does not assign one edge to one current.
The approvals block on the brochure, opened November 7, 2026, says Cuponal has been approved for use in equipment by Germanischer Lloyd, Det Norske Veritas, ABS, Bureau Veritas, Lloyds Register of Shipping, SABS, ULA, National Power Supply Company, National Grid Company, and electrical and water utilities. It lists applications that include LV, MV, and HV distribution, switchboards, motor control centres, panel boards, busbar chambers, busbar trunking, rectifiers, fuse gear, and transformer substations. Those names are the brochure's list. They do not assign a voltage or a current to a section. Short-circuit testing is described as having been done by ASTA, KEMA, and Electrisches Prüfamt, München. The brochure does not print a short-circuit current.
What to copy onto the bar line
- Document: Cuponal brochure, or ASTM B1005-17, as opened November 7, 2026.
- Cladding: 15 percent by volume for standard Cuponal rectangular or round bar, or 20 percent for a high-aspect, L, or T Cuponal profile.
- ASTM class, when that is the document: 20A, 25A, 30A, 20H, 25H, or 30H.
- Size: width 10 to 120 mm, thickness 3 to 15 mm, diameter up to 40 mm, length 4000 mm or up to 6000 mm, for a standard Cuponal supply.
- Edge: square or round, from the brochure. The ASTM page names edge contours and does not print the contour list on the abstract.
- Solid copper, when the bar stays C110, stays on the copper and aluminum page.
Questions these pages answer
Is 15 percent Cuponal a B1005 class?
The ASTM page opened November 7, 2026 lists 20, 25, and 30 volume percent. The Cuponal pages list 15 percent for standard rectangular and round bar. Those are different order lines.
Does a 20 percent Cuponal profile use Class 20A?
Both lines say nominal 20 volume percent, as of November 7, 2026. Cuponal's 20 percent line is the high-aspect exception and the L or T profile. Class 20A is annealed rectangular bar under ASTM B1005, and Class 20H is the hard-worked class. The brochure does not call the profile Class 20A.
What length does the brochure print?
Standard length is 4000 mm and maximum length is 6000 mm, as of November 7, 2026. Width is 10 to 120 mm and thickness is 3 to 15 mm on that same supply block.
Sources
The 15 percent and 20 percent cladding, the standard supply dimensions, BS 159:1957, and DIN 43670 Part 2 are from the Cuponal brochure. The Bruker busbar page repeats the 15 percent rectangular and round line, the 20 percent high-aspect and profile line, and the equal-dimension substitution. The six class names are from the ASTM B1005-17 page. All three were opened November 7, 2026.