Skip to the guide

Power connections

Busbar Insulation Boots: PVC or Polyolefin

Use the Galathermo PVC boot from 1.25 mm at 3.3 kV through 4.50 mm at 38.0 kV. Use the polyolefin boot when the page's halogen-free line applies, from 1.0 mm at 12 kV.

Rust Belt Industrials · November 11, 2026 · 5 min read

On this page

Use the Galathermo PVC boot when the joint follows that sheet's thickness table, including the 3.3 kV row. As of November 11, 2026, issue 2 dated February 2026 lists 1.25 mm at 3.3 kV, 2.00 mm at 12.0 kV, 2.50 mm at 18.0 kV, 3.00 mm at 24.0 kV, and 4.50 mm at 38.0 kV, with a continuous operating temperature of -20°C to 115°C. Use the polyolefin boot when the order needs the halogen-free line on Galathermo's polyolefin page. As of the same day, that page lists a minimum thickness of 1.0 mm at 12.0 kV, 1.4 mm at 18.0 kV, 1.8 mm at 24.0 kV, and 2.5 mm at 36.0 kV, with a continuous temperature of -40°C to 115°C. Heat-shrink tubing on the bar, rather than a boot on the joint, is the shroud and tubing page.

Both boots cover a joint, and the thickness tables start at different voltages

The PVC sheet and the polyolefin page both describe a flexible boot, or shroud, for busbar and switchgear connections, including tees and elbows, that can be installed and removed. Both say the cover is for outdoor or indoor use and name resistance to UV and ozone. The PVC sheet says the boot is tested to ANSI C37.20.2 for medium-voltage switchgear application up to 36 kV. Its thickness table still has a 38.0 kV row at 4.50 mm. Copy the ANSI line when the request cites that standard up to 36 kV. Copy the 38.0 kV row when the request cites that row. The polyolefin page says the boot is for connections up to 36 kV, and its highest thickness row is 36.0 kV at 2.5 mm. It does not print an ANSI C37.20.2 line. It does print halogen free. The PVC sheet does not print a halogen-free line.

Galathermo boot thickness rows opened November 11, 2026. PVC is issue 2, February 2026. Polyolefin is the product page.
Voltage on the sheetPVC minimum thicknessPolyolefin minimum thickness
3.3 kV1.25 mmNo row on the polyolefin page
12.0 kV2.00 mm1.0 mm
18.0 kV2.50 mm1.4 mm
24.0 kV3.00 mm1.8 mm
36.0 kV polyolefin, or 38.0 kV PVC4.50 mm at 38.0 kV2.5 mm at 36.0 kV

The PVC boot is issue 2, from -20°C to 115°C

The vinyl sheet opened November 11, 2026 is issue 2, February 2026. It calls the part a bus bar insulating shroud or boot, made from PVC, for connections up to 36 kV. Qualification report QR 1018 is named on the sheet. The recorded values are dielectric strength 16 kV/mm minimum to ASTM D149, tensile strength 12 N/mm² minimum to ASTM D638, elongation 350 percent minimum to ASTM D638, density 1.23 g/cm³ to ASTM D792, water absorption 0.5 percent maximum to ASTM D570, hardness 65 plus or minus 5 Shore A to ASTM D2240, continuous operating temperature -20°C to 115°C to IEC 216, and flammability pass to UL 94 V-0. The sheet says fasteners are included and describes an overlapping closure as added protection against flashover. It says new molds can be developed. It does not print a catalog code next to a bar width.

The polyolefin boot adds the -40°C row and the halogen-free line

The polyolefin page opened November 11, 2026 calls the part Busboot polyolefin, made from cross-linked polyolefin, for connections up to 36 kV. Qualification report QR 1031 is named on the page. The visible specification table prints tensile strength 9 N/mm² minimum to ASTM D638, ultimate elongation 300 percent minimum to ASTM D638, water absorption 0.5 percent maximum to ASTM D570, and hardness 45 plus or minus 10 Shore D to ASTM D2240. Low-temperature flexibility is no cracking after 4 hours at -40°C to ASTM D2671. Heat shock is no cracking or flowing after 30 minutes at 90°C to ESI 09-11. Continuous temperature is -40°C to 115°C to IEC 216. Dielectric strength is 22 kV/mm minimum to ASTM D149. Volume resistivity is 1 x 10^13 ohm cm minimum to ASTM D257. Dielectric constant is 5 maximum to ASTM D150.

Shore A on the PVC sheet and Shore D on the polyolefin page are different hardness scales. Copy the scale the sheet prints. At a shared voltage the polyolefin minimum thickness is the thinner row: 1.0 mm against 2.00 mm at 12.0 kV, 1.4 mm against 2.50 mm at 18.0 kV, and 1.8 mm against 3.00 mm at 24.0 kV. A 3.3 kV joint has a PVC row at 1.25 mm and no polyolefin row on the page that opened. The top rows stay on their own voltages: 4.50 mm at 38.0 kV for PVC, and 2.5 mm at 36.0 kV for polyolefin.

What to copy onto the boot line

  • Boot: Galathermo PVC, issue 2, February 2026, or Galathermo polyolefin, as opened November 11, 2026.
  • PVC voltage row: 1.25 mm at 3.3 kV, 2.00 mm at 12.0 kV, 2.50 mm at 18.0 kV, 3.00 mm at 24.0 kV, or 4.50 mm at 38.0 kV.
  • PVC standard line: ANSI C37.20.2 up to 36 kV, when the request cites that line.
  • PVC temperature: -20°C to 115°C. Report QR 1018.
  • Polyolefin row: 1.0 mm at 12.0 kV, 1.4 mm at 18.0 kV, 1.8 mm at 24.0 kV, or 2.5 mm at 36.0 kV.
  • Polyolefin temperature: -40°C to 115°C. The page lists halogen free. Report QR 1031.
  • Joint shape: tee, elbow, or the shape the drawing shows. Neither page prints a width next to the thickness row.

Busbar insulation boot note

Name the PVC boot or the polyolefin boot. Copy the voltage row and the continuous temperature from that sheet.

This prepares a request. It does not send one.

Questions the two boot sheets answer

Which boot has a 3.3 kV row?

The PVC sheet, as of November 11, 2026, lists 1.25 mm at 3.3 kV. The polyolefin thickness list starts at 12.0 kV and 1.0 mm.

Which boot prints -40°C?

The polyolefin page prints a continuous limit of -40°C to 115°C, and a 4 hour flexibility test at -40°C with no cracking, as of November 11, 2026. The PVC sheet prints -20°C to 115°C.

Are 36 kV and 38 kV the same row?

The PVC standards line says ANSI C37.20.2 up to 36 kV, and the PVC thickness table's highest row is 38.0 kV at 4.50 mm, as of November 11, 2026. The polyolefin page's highest row is 36.0 kV at 2.5 mm.

Sources

PVC thickness, the ANSI line, QR 1018, and the -20°C to 115°C cell are from Galathermo issue 2, February 2026. Polyolefin thickness, the halogen-free line, QR 1031, and the -40°C to 115°C cell are from the Galathermo polyolefin page. Both were opened November 11, 2026.